Wondering how thin a machined wall can safely be? These cnc wall thickness guidelines put the usual floor at about 0.8 mm for metal and 1.5 mm for plastic, with thinner walls possible but riskier and costlier.
This page is one part of the wider set of cnc design guidelines on this site, which cover the other features that shape machining cost and quality.
| Item | Value |
|---|---|
| Recommended wall, metal parts | 0.8 mm |
| Absolute minimum wall, metal parts | 0.5 mm |
| Recommended wall, plastic parts | 1.5 mm |
| Absolute minimum wall, plastic parts | 1 mm |
| Maximum unsupported wall height-to-thickness ratio | 15:1 |
The figures come from the JLCCNC design guideline (last updated Aug 20, 2025) and the RapidDirect thin-wall guide (published May 22, 2026). Shop limits can change, so check the source before you rely on them.
Why thin walls are hard to machine
A thin wall flexes under the cutting tool. JLCCNC notes that thin walls need multiple passes at low cutting depths, which can easily lead to vibration, deformation and breakage.
The BYU Design Review makes the same point: thinner walls are less stiff. RapidDirect adds that stiffness falls with the cube of thickness, so a small cut in thickness costs a lot of rigidity.
The same RapidDirect guide groups the main causes of warping into a short list:
- Cutting force: radial forces push the wall away from the end mill, and it springs back once the tool passes.
- Residual stress: rolled or extruded stock holds internal stress, and removing material breaks that balance, so the part warps.
- Clamping: standard vise hard jaws can compress thin walls and leave localized deformation.
The result is deceptive. According to RapidDirect, a part may measure perfectly inside the machine but drift out of tolerance once it is removed.
What is the minimum wall thickness for CNC parts?
Published guides broadly agree on a design target of 0.8 mm for metals and 1.5 mm for plastics. The JLCCNC guideline and the BYU Design Review both give those numbers, while a September 2023 Xometry Europe article republished on Wevolver lists 0.794 mm for metals and 1.5 mm for plastics.
Individual shops set their own limits. In its CNC milling design guidelines, Protolabs recommends features thicker than 0.51 mm and requires a nominal part thickness above 1.02 mm.
That spread is normal, because Hubs points out that no industry-wide specific standards exist for CNC design. Treat every number as a shop-specific limit and confirm it with whoever will cut your part.
RapidDirect splits its limits by material, which is useful when you are not working in aluminum:
| Material | Absolute limit (mm) | Recommended (mm) |
|---|---|---|
| Aluminum (6061-T6) | 0.5 | 0.8 |
| Steel / stainless | 0.8 | 1.5 to 3.0 |
| Titanium alloy | 1.0 | 2.0 to 3.0 |
| Plastics | 1.0 | 1.5 |
The same page calls 0.8 mm the safe floor for mass production in aluminum. It also describes a drone project where raising thickness from 0.5 mm to 0.8 mm dropped the scrap rate from 45% to 2%, which is one vendor-reported case but shows why the absolute minimum is not a design target.
Wall height matters as much as thickness
A wall is not thin by thickness alone. RapidDirect defines it by the ratio of thickness to unsupported height, and gives a universal upper limit of 15:1, so a wall 1 mm thick must not exceed 15 mm in height.
Ribs can support a tall wall, but they have limits too. The same guide says a rib should be only 50% to 60% of the main wall’s thickness, and its height-to-width ratio should stay under 3:1 so the rib itself does not vibrate during machining.

How to design thin walls that machine well
Work through these steps before you send a model out for quotes:
- Start from the recommended thickness for your material, not the absolute minimum.
- Stay within the 15:1 limit that RapidDirect gives for unsupported wall height, so a wall 1 mm thick stays at or under 15 mm tall.
- Design for the largest, shortest tool that can reach the feature. Hubs says this simplifies production, and it recommends a cavity depth of 4 times cavity width.
- Loosen tolerances on thin features where function allows, because JLCCNC notes that smaller tolerances cost more to produce and inspect.
- If the wall must be thinner than machining comfortably allows, ask whether another process fits. The Xometry Europe article suggests sheet metal fabrication for thinner walls.
If a thin wall also needs tight flatness or perpendicularity, the gd&t basics explain how to specify that clearly on a drawing.
Holes and threads placed in or near thin walls add constraints of their own, which cnc thread and hole design covers.
Frequently asked questions
Can CNC machining make walls thinner than 0.5 mm?
Show answer
JLCCNC lists 0.5 mm as the absolute minimum wall for metal, and Protolabs recommends features thicker than 0.51 mm. For thinner walls, the Xometry Europe article points to processes such as sheet metal fabrication.
Why do plastic parts need thicker walls than metal parts?
Show answer
Guides list 1.5 mm for plastic against 0.8 mm for metal. RapidDirect describes plastics as prone to bending and warping, and highly sensitive to temperature and clamping force.
How thin can steel or titanium walls be?
Show answer
RapidDirect lists an absolute limit of 0.8 mm for steel and stainless, and 1.0 mm for titanium alloy. Its recommended values are higher, at 1.5 to 3.0 mm for steel and stainless, and 2.0 to 3.0 mm for titanium, which it describes as extremely heat-sensitive. The figures are on its thin-wall guide.
Is there an industry standard for minimum wall thickness?
Show answer
Hubs says no industry-wide specific standards exist for CNC design. Numbers differ between shops, so confirm the limit with your machinist before you finalize a model.



