Plain-language guides to precision CNC manufacturing

Search

Surface Finishes for Machined Parts Explained

cnc surface finishes

Not sure which of the many cnc surface finishes your part needs? Start with the standard Ra 3.2 μm as-machined surface, and add a finish only when you need looks, corrosion protection or wear resistance.

Finishing is one step in the wider workflow of precision cnc machining, so treat this page as a companion to that overview.

Item Value
Standard as-machined roughness Ra 3.2 μm (125 μin)
Finer cutting-pass options Ra 1.6, 0.8 or 0.4 μm (63, 32 or 16 μin)
Typical Type II anodized coating 4-12 µm
Typical Type III (hardcoat) thickness About 50 µm, up to 125 µm
Growth of a 50 µm anodized coating About 25 µm outward, 25 µm inward
Bead blasting grit used by one network #120 grit

These figures come from a CNC surface finish guide on mfgrobots.com. Figures can change, so check the source before you rely on them.

Surface roughness: what Ra tells you

Every machined part carries marks that follow the cutting tool path. Ra is the average deviation of the machined profile from an ideal surface, and it is the number most drawings use to describe that texture, according to a manufacturing guide.

A quick reference from Fictiv’s finish specifications maps common Ra values to typical uses:

  • Ra 3.2 μm (125 μin): standard CNC finish, cosmetic acceptable.
  • Ra 1.6 μm (63 μin): fine finish, good for O-ring seals.
  • Ra 0.8 μm (32 μin): precision finish, adds cost.
  • Ra 0.4 μm (16 μin): ground finish, expensive.

Hubs adds that surface finishes can serve either a functional or aesthetic purpose. Knowing which one you need keeps you from paying for the wrong thing.

As-machined surfaces and finer cutting passes

As-machined parts show minor visible tool marks. The standard as-machined Ra is 3.2 μm (125 μin), and a finishing cutting pass can bring it down to 1.6, 0.8 or 0.4 μm (63, 32 or 16 μin), as the same guide explains.

The standard finish keeps the tightest dimensional tolerances and adds no cost. Tighter Ra values increase part cost because they need additional machining steps and stricter quality control.

Xometry’s finish page says the same about improving roughness to 63, 32 or 16 μin: it increases the number of operations and likely the cost. For the wider picture of what drives price, read our overview of cnc machining cost factors.

Bead blasting and other mechanical finishes

Bead blasting produces a uniform matte or satin finish and reduces visible tool marks. Glass beads are propelled by pressurized air, and the guide says Protolabs Network generally uses #120 grit, per the mfgrobots guide.

Three points matter when you specify it:

  • It is mainly an aesthetic finish.
  • It is a manual operation, so the final look depends partly on operator skill.
  • Critical features such as holes can be masked to prevent dimensional change.

Smoothing or polishing can lower Ra and improve appearance, but they remove material and can affect dimensional tolerances. If a bore or a mating face is tight, say so on the drawing.

Anodizing: Type II and Type III

Anodizing forms a thin ceramic oxide layer that protects against corrosion and wear. It works on aluminum and titanium only, and the coating can be dyed for color, according to the guide.

  • Type II: coatings typically fall in the 4-12 µm range. Clear, undyed coatings are usually 4-8 µm and black-dyed ones 8-12 µm. It gives good corrosion resistance but limited wear resistance.
  • Type III (hardcoat): typical thickness is about 50 µm unless specified otherwise, and coatings can reach 125 µm. It needs tighter process control, which raises cost.

The coating grows both outward and inward. A 50 µm coating extends about 25 µm above the original surface and removes about 25 µm below it, so a 1.00 mm cylinder measures about 1.05 mm afterwards (same source).

Areas that need tight dimensions or electrical conductivity, such as threaded holes, can be masked. The guide points readers to MIL-A-8625 for detailed anodizing specifications.

cnc surface finishes Grooved surface
A teal metallic surface has closely spaced vertical grooves.

Powder coating and other coatings

Powder coating adds a thin protective polymer layer. It can be applied to any metal and is often combined with bead blasting for a uniform, smooth look, the guide notes.

Fictiv’s finish specifications give a thickness of 2-6 mils and a cure at 350-400°F. Xometry describes the result as a layer more durable than standard painting methods.

Hubs advertises 15+ surface finishing options. Its table pairs several coatings with specific metals:

  • Chromate conversion coating: aluminum.
  • Electroless nickel plating: mild steel, aluminum and stainless steel.
  • Passivation: stainless steel.

How do you choose a finish for your part?

Work through the decision in order, and stop as soon as the part meets its requirement:

  1. Define the purpose. Decide whether the surface is about looks, corrosion, wear or fit.
  2. Mark your A-side and B-side. Hubs describes the A-side as the most aesthetically important surface and the B-side as the one hidden after assembly (Hubs finishing page).
  3. Keep roughness at the standard unless a function demands more. The standard as-machined Ra is 3.2 μm (125 μin), and finer grades need additional machining steps.
  4. Allow for coating growth and masking. Note threads and bores on the drawing.
  5. Check cost last. Type III hardcoat is the most expensive finish the mfgrobots guide discusses.

Finishing can leave marks too. Hubs notes that hang marks from anodizing are a common aesthetic defect, and its cosmetic criteria allow B-side surfaces up to 2 minor defects. Calling out the A-side lets the finisher place those marks out of sight.

If you are still validating a design, the cnc prototyping guide covers that stage in more detail.

Frequently asked questions

What is the standard CNC surface finish?

Show answer

The standard as-machined Ra is 3.2 μm (125 μin), with visible tool marks, according to the mfgrobots guide.

Does a smoother finish cost more?

Show answer

Usually yes. Tighter Ra values need extra machining steps and stricter quality control, the guide says, and Fictiv lists Ra 0.4 μm as a ground, expensive finish.

Does anodizing change part dimensions?

Show answer

Yes. The coating grows outward and inward, so a 50 µm coating adds about 25 µm to each surface (mfgrobots guide). Mask critical features such as threaded holes.

Which metals can be anodized?

Show answer

The guide says anodizing is compatible with aluminum and titanium only (mfgrobots). Other metals need a different coating, such as powder coating, which can be applied to any metal.